How To Clean Your Toyota 4Runner's Throttle Body?

The Toyota 4Runner's throttle body is an integral component that plays a pivotal role in supplying air to the engine's combustion chambers, hence affecting the proper formation of the air-fuel mixture. Essentially, the more you push down on the accelerator pedal, the wider the throttle opens, allowing a larger volume of fuel into the engine's cylinders. The functioning of the throttle body is directly related to the amount of the air-fuel mix. 

Over time, the throttle body may gather dust and dirt, which enter along with the air during the combustion process.

This accumulation starts settling on the body, hampering the smooth functioning of the throttle. If the throttle body becomes too dirty, your Toyota 4Runner will start showing signs of it. Here are some symptoms of a clogged throttle body:

• Irregular idle speed;
• Stalling when stepping on the throttle pedal;
• Loss of throttle response - sluggish acceleration;
• Increased fuel consumption; loss of vehicle power

If you're experiencing these symptoms, and it's been a while since you last cleaned your throttle body, then it's time to give it a good clean.

What tools do you need to clean your Toyota 4Runner's throttle body?

You'll need a handful of simple items to clean the throttle body, most of which you likely already have in your garage. 

They include:

• Throttle body cleaner, or Throttle body and Air Intake cleaner (both are similar);
• Carburetor cleaner - this may come in handy;
• Brush;
• Cloth or rag;
• Screwdriver

It's generally advisable to clean the throttle body approximately every 75,000 miles (121,000 km). While there's no hard-and-fast rule or specific schedule for this, keeping the throttle body clean can significantly improve the performance of your Toyota 4Runner. If you start noticing unusual symptoms, it might be a signal that it's time for a cleaning session.

How to clean your Toyota 4Runner's throttle body?

The throttle body can be cleaned in two ways - either with the throttle body in place on the 4Runner or by removing it. In this article, we'll demonstrate the method without removing the throttle from the 4Runner. 

Although this method may not be as thorough as the one involving the removal and complete cleaning of all components, it is simpler and still quite effective, especially if your throttle body isn't heavily soiled or malfunctioning.

Disconnect the negative battery terminal

Before you start, disconnect the negative terminal from the battery. It's a safety measure to prevent any potential electrical shock and ensure your Toyota 4Runner is completely de-energized.

[amazon_products node_id="125" count="2"][/amazon_products]

Unhook the air duct from the throttle body

You'll need to unhook the air supply hose that runs from the air filter to the throttle body. This is typically fastened with a clamp, but your 4Runner may have a different method. Make sure to disconnect it prior to removal.

Disconnect the hoses and sensors attached to the throttle

The throttle body has various wires and tubes connected to it, some of which are sensors and others through which coolant flows. Make sure to keep these pipes vertical and plug them with a spark plug to avoid any fluid leakage when you disconnect them.

Label all sensors and hoses

Once you've cleaned the Toyota 4Runner's throttle body, you'll need to reassemble everything in its rightful place. If there are too many wires, things can get confusing. Hence, label and mark everything you disconnect, so you know exactly what goes where after the cleaning process.

Apply throttle cleaner to the surface

Spray some cleaner onto the throttle body. Give it some time to do its magic. If there are stubborn stains or deposits, let the cleaner sit for about 3-5 minutes. That should be enough to loosen them up.

[amazon_products node_id="190" count="3"][/amazon_products]

Begin the manual cleaning of your Toyota 4Runner's throttle body

Now you can start scrubbing the throttle body using a brush (make sure it's not too hard to avoid scratching the blade), a cloth, or a cotton swab. Don't worry if you can't remove all the dirt at once. There's no harm in applying the cleaner again and repeating the process until you achieve complete cleanliness. A well-cleaned throttle body should look almost shiny and free from any deposits or contamination.

[amazon_products node_id="167" count="3"][/amazon_products]

Reassemble the entire system

Once you're done with the throttle body cleaning, it's time to reassemble everything. Make sure that everything is functioning as it should and check for any unusual noises or symptoms after the process.

How to adapt your Toyota 4Runner's throttle body

In newer models of the Toyota 4Runner, the throttle is electronic and is operated by an electronic pulse instead of a traditional cable. A special throttle position sensor is tasked with monitoring the position of the throttle blade. Before firing up the engine, this blade sits perfectly straight, at an angle of 90 degrees.

It fits snugly against the upper and lower walls, preventing excessive air from getting in. However, over time, grime can accumulate on the walls of the air channel or the blade. This can prevent the throttle from closing completely, causing it to stick in the same position.

The sensor detects this position, and the 4Runner's onboard computer registers it as the new reference point.

This means the throttle blade's neutral position, accounting for the thickness of the layer of grime, becomes the new benchmark, as far as the computer is concerned. This is an entirely normal occurrence, and it's designed to ensure the engine continues to run smoothly.

However, once you've cleaned the throttle body and restored the surface to its original state, the 4Runner's computer might get a little confused.

With no indicators to inform it that there's no longer anything preventing the throttle blade from closing completely, the vehicle's computer will continue to operate under the assumption that the grime is still there and keep the blade in the previously recorded position.

This creates a small gap between the throttle walls and the blade, allowing at least a few millimeters of air to pass through.

As a result, the 4Runner's computer operates under the assumption that the throttle pedal is continually engaged, even when it's not, and lets more air flow into the cylinders through the gap.

This can be detrimental to the engine; it's continually under load, which is particularly noticeable at idle. Instead of the expected 800 rpm, it might be running at 1500–2000 rpm. This can cause the engine to overheat and reduce its longevity.

Therefore, it's crucial to recalibrate the blade to its factory position after cleaning the throttle valve.

The throttle valve adaptation algorithm is universal for many Toyota 4Runner models.

Get the engine up to operating temperature, then shut it off and wait 5-10 seconds. Turn the ignition on and wait 3 seconds. Then, press the throttle pedal 5 times over 5 seconds and release it.

If this doesn't achieve the desired result, it means that your Toyota 4Runner's system is programmed differently. The throttle valve adaptation algorithm should be specified in your 4Runner's owners manual.

Summing It All Up

Cleaning your 4Runner's throttle body is a crucial maintenance task as it prevents grime from accumulating on the blade or gaps from forming between the blade and the body.

During this cleaning process, patience and meticulousness are key to achieving the desired outcome.